+ 86-574-56118361

Categories All

Mofani oa Ts'ebeletso e le 'ngoe Bakeng sa Mould Ente ea Plastiki


Theknoloji ea ente ea hlobo e chesang

Nako: 2021-03-09 Hits: 202

Hot runner gating system can be understood as an extension of injection molding machinery. The function of the hot runner system is to deliver the thermoplastic melt to the vicinity of the molding die or directly into the die adiabatically.


The hot runner can be heated independently, but thermally insulated in the injection mold, so that it can individually compensate for the heat loss caused by contact with the "cold" mold. Hot runner molds have been successfully used to process various plastic materials. Almost all plastic materials that can be processed with cold runner molds can be processed with hot runner molds.


The smallest part is less than 0.1 grams, and the largest part is more than 30 kilograms. Hot runner molds are widely used in the fields of electronics, automobiles, medical care, daily necessities, toys, packaging, construction, and office equipment.

injection mold hot runner


A successful hot runner mold application project requires multiple links to be guaranteed.


Among the most important are two technical factors:

One is the control of plastic temperature;

The second is the control of plastic flow.


A typical hot runner system consists of the following parts:

   1) Hot runner plate (MANIFOLD);

   2) Nozzle;

   3) Temperature controller;

   4) Auxiliary parts.


Advantages of hot runner mold:


  1) Shorten the molding cycle of parts;

   2) Save plastic raw materials;

   3) Reduce waste and improve product quality;

   4) Eliminate subsequent processes, which is conducive to production automation;

   5) Expand the application of injection molding technology.


At the same time, there are also shortcomings such as rising mold costs, high manufacturing process equipment requirements, and complicated operation and maintenance.


Types and applications of hot runner systems


When applying hot runner technology, the correct choice of gate type is very important. The gate type directly determines the selection of hot runner system components and the manufacture and use of molds. Therefore, according to the different gate types, the hot runner system can be divided into three types: hot tip hot runner system, sprue hot runner system, and valve hot runner system. Each type of hot runner system has its important application. Features and scope of application.


Many factors need to be considered when selecting the types of gates and hot runner systems, the most important of which are the type of plastic matrix and additives, the weight and size of the parts, the quality requirements of the parts, the tool life and the production requirements of the parts.


1. Hot Tip Hot Runner System (HOT TIP)

Its working principle is to combine the HOT TIP at the front end of the nozzle with the cooling system to precisely adjust and control the plastic molding processing temperature at the gate. Therefore, the manufacturing material and shape design of the nozzle insert HOT TIP are very important.


hot tip hot runner

HOT TIP hot runner system can be used to process most crystalline and amorphous plastics such as PP, PE, PS, LCP, PA, PET, PBT, PEEK, POM, PEI, PMMA, ABSPVC, PC , PSU, TPU, etc. Generally speaking, hot tip gates are mostly used for the processing of small and medium-sized parts, especially for the processing of small parts.


The diameter of the gate section is mostly between 0.5mm-2.0mm. The determination of the diameter of the gate section is mainly determined by the weight and wall thickness of the part, and of course the material and part quality requirements must also be considered. If a gate with a smaller cross-sectional diameter is used, the gate will be closed quickly after the injection filling stage is completed, the gate marks on the part will be small, and the surface of the part will have good appearance and quality.


If the gate diameter is too small, the shear rate will be too high when the plastic flows through the gate, which will seriously damage the molecular chain structure of the plastic melt or the added materials in the plastic, resulting in unqualified products that cannot meet the requirements of use. In the selection of the gate size, the usual practice is to initially determine the gate size according to the wall thickness at the part gate: gate diameter = (0.75-1.0) the wall thickness at the part gate. The smaller value is used for processing easy-flow plastics, and the larger value is used for processing hard-flowing plastics or plastics that are sensitive to shear.


Usually, the hot tip gate is opened directly on the part, but it can also be opened on the cold runner and then the cold gate is opened on the part. This is a mold system that combines hot runner and cold runner. When using hot tip gates to make plastic parts, there will always be more or less gate marks on the parts. Many times the gate marks will be higher than the surface of the part, affecting the beauty of the part or affecting the assembly with other parts. Therefore, when selecting the gate location, try to place the gate in the recessed concealed part on the part.


2.Sprue gate hot runner

In the sprue hot runner system, the plastic enters the mold cavity through an open runner (OPEN PIPE). The plastic flow pressure loss at the gate is small. The sprue hot runner system is more suitable for injection molding of parts with medium size and weight.


sprue gate hot runner

The advantage of using the sprue hot runner system is that the plastic undergoes a low shear rate when it flows through the gate and fills the mold, the residual stress after the part is formed is small, the degree of deformation is small, and the mechanical strength of the part is relatively good. Compared with hot tip gates, sprue gates are larger in size, so gate marks may also be larger.


Therefore, under normal circumstances, molds with strict requirements for the aesthetics of the gate often use plastic injection molding; and internal structural parts that do not require high aesthetics for the gate can be manufactured by a sprue-type hot runner system.


People often use the sprue sprue in combination with the cold runner, that is, the sprue nozzle is used as the main runner, and the sprue sprue is opened on the cold runner. In this application, the sprue gate can be opened larger to facilitate the flow of the plastic, because no one cares about the size of the gate marks on the cold runner.


Similar to the application of hot-tip hot runner systems, the control of the plastic temperature and mold temperature at the gate is extremely important. A separate cooling circuit needs to be set up around the gate. Because the size of the sprue gate is relatively large, if the temperature at the gate is not well controlled, it is more likely that the gate cannot seal the plastic flowing after the mold is opened.


The nozzle inserts of the sprue hot runner system also have a variety of sizes and shapes and changes in manufacturing materials. The types of plastics to be processed (such as crystalline plastics or amorphous plastics) and the cooling conditions of the gate must be considered.


3.  Valve gate hot runner

This type of hot runner system has many advantages that hot tip and sprue runner systems cannot have. For example, the gate opening and closing time can be controlled artificially, the gate is smooth and flat, and the application technology field of hot runner technology can be expanded.

valge gate hot runner

Because the valve gate is closed by the mechanical action of the valve needle, it is not limited by the cooling time of the plastic at the gate, so the valve gate runner system can sometimes greatly shorten the production and molding cycle of plastic parts. The gate size can also be opened larger, which is very good for processing shear-sensitive plastics. The valve gate method can process small parts weighing several grams, as well as large parts weighing several kilograms. All kinds of engineering plastics can be used to process production parts with valve gates. If there are multiple cavities of different sizes in a set of molds, if a valve runner system is used, the opening and closing time of each gate can be controlled to realize the respective adjustment and control of the flow of each cavity. This is of great significance to one-mold multi-cavity molds with very different shapes and sizes. For high-productivity, multi-layer parting surface molds, only through the use of valve-type hot runner system to achieve.